Phone icon

Kerakoll Proflow Finish Floor Smoothing Compound

£20.02 (inc VAT)

10 in stock (can be backordered)

Quantity:

Description

Kerakoll Proflow Finish Floor Smoothing Compound is a high performance fibre reinforced single component smoothing compound. Rapid setting with prolonged working time. The advanced formulation allows for complete control under the trowel whilst maintaining high flow properties, exceptional repair properties, extended working and wet edge time and delivers a flawless surface finish upon drying.

Kerakoll Proflow Finish is designed for self-smoothing adjustment of irregular and uneven substrates, with rapid setting and drying, compensated shrinkage. For thicknesses from 3 to 60mm.

Kerakoll Proflow Finish can be used with the following covering materials:  LVT and design flooring, vinyl, sheet vinyl and safety flooring, hardwood floors, textiles, rubber, PVC, linoleum, carpet and raised floors.

Kerakoll Proflow Finish  can be used on the following substrates:

  • Mineral screeds made with Kerakoll Keracem Eco as binder or pre-mixed product
  • Cement-based screeds
  • Calcium sulphate-based screeds
  • Prefabricated concrete or fresh concrete castings
  • Ceramic floors
  • Flooring grade plywood
  • Flooring grade asphalt/bitumen
  • Epoxy DPM
  • Internal floors in domestic, commercial and industrial applications

Do not use in external applications, or areas that are continually submerged.

Preparation of substrates:

The substrate must comply with current British standards and industry regulations. In general, substrates must be free of dust, oil and grease, free from any moisture rising, with no loose, flaky or imperfectly anchored parts such as residues of cement, lime, paint coatings and adhesives, which must be completely removed. The substrate must be stable, without cracks and have a functioning DPM within the subfloor. If no DPM is present, a surface epoxy DPM must be applied before installing resilient floor coverings. Kerakoll Proflow Finish can be used to pre-smooth the floor at 95% RH prior to installing a surface epoxy DPM. In particular, substrates must be treated with a suitable primer such as Kerakoll Active Prime Fix, diluted or neat according to the product datasheet, linked below.

Mixing:

Pour 4.5 − 5.2 l of clean water into a clean container; then pour in a bag of Kerakoll Proflow Finish, while shaking. Mix with a mechanical mixer until the mixture is smooth, lump-free and self-smoothing. Larger quantities of Kerakoll Proflow Finish may be prepared in suitable mixers. After the first mixing, it is advisable to leave the mixture to rest for approx. 2 minutes and then mix again briefly. Kerakoll Proflow Finish features a high degree of self-levelling capacity. Adding extra water does not improve its workability, and may cause shrinkage in the plastic phase of drying and result in less effective final performance with a reduction in surface hardness, surface finish, compressive strength and adhesion to the substrate.

Application:

Kerakoll Proflow Finish is generally applied with a flooring trowel, cam rake, pin level or mechanical pump. Application with mechanical pumps allows the installer to very quickly achieve a smooth high-thickness application for large areas. The use of an aeration tool or spike roller is fine/allowed, but is not required to further improve the surface finish of Kerakoll Proflow Finish, but will work to remove entrapped air from the mixture. If an additional application of Kerakoll Proflow Finish is required once the initial application has been completed, the first installation layer must first be hardened and ready to accept foot traffic and additional application, this is generally after 3.5 hours. The initial layer of Kerakoll Proflow Finish must be primed with a neat coat of Kerakoll Active Prime Fix prior to subsequent applications. In the case of low temperatures and high humidity it is advisable to keep the environment ventilated during application and during the hours immediately following application, in order to avoid the formation of condensation on the surface of the smoothing compound during the setting phase.

Technical Data:
Appearance: grey pre-mixed
Apparent volumetric mass: ≈ 1.17 g/dm3
Mineralogical nature of inert material: silicate – crystalline carbonate
Grading: 0-600 μm
Mixing water: ≈ 4.5 – 5.2 l / 1 bag 20 kg
Specific weight of the mixture: ≈ 2.01 g/dm3 UNI 7121
Self levelling time: ≈ 30 min.
Temperature range for application: from +5 °C to +30 °C
Maximum thickness: from 3 to 60 mm
Foot traffic: ≈ 90 min.
Waiting time before laying: – LVT, vinyl, sheet vinyl, safety flooring and all other resilient floor coverings ≈ 3.5 hrs, – resins and paint ≈ 12 hrs
Coverage: ≈ 1.481 kg/m2 per mm of thickness

Product Datasheet

Click here to view this product on the Manufacturers website.

Additional information

Weight 20 kg
× Chat to us on WhatsApp